Download Heatline C28 manual. You have chosen to download this manual. Heatline C28, please click on the PDF link below. The boiler’s ‘Log Book’ must be completed at each Service visit. By means of a manual switch the C24/C28 can be set to operate in one of two operating modes, . Boiler Manuals for the Heatline Compact C28 appliance.
|Published (Last):||14 September 2004|
|PDF File Size:||18.97 Mb|
|ePub File Size:||8.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
Landlords Landlords cover Landlords repair Landlords insurance. Ideal Commercial Boiler Spares. X This part also fits Fit the replacement body in reverse order ensuring that the pump washers are sound and fitted correctly and the polarity of the electrical connections are correct Put in the new sensor.
Hi this problem first occurred a few weeks ago, ill try and make it as clear as possible, any help appreciated. If so that usually spoils the motor. You should unscrew the integral pump vent plug. Direct heating spares is the leading supplier of plumbing and gas heating boiler spares in the uk and we fully understand the importance of heating and hot water especially during the winter seasons.
Underfloor heating contact fault. Log in or Register. Not to offend you but thanks for reading and your reply in the first place. Make sure that the sensor is clipped to the tube.
Fluctuation of flame signal. Appreciate all your advice though regards, Gary. I would consider a boiler change although most of us are a bit cash straped at the moment it may be money cc28 spent.
Fault memory will allow you to display up to 10 most recent fault codes Table 1.
Save to your online account What’s this? Your boiler should be pressurised to between 1 to 1. Replace user interface PCB. After activating this function system will need to be manually re-set. Re-connect sensing manul and all the electrical leads.
That can be achieved by fitting dip switch number 5 into the position ON. No water in the installation: Your name or email address: About us Contact us Emergencies. Verify the flow and return heating sensor connections. Verify that the sensor is connected to the main board and the shunt is removed. Replace faulty sensors F85 Flow and return heating sensors fault Verify temperature sensors connections F86 Underfloor heating contact fault Verify the sensor connections.
On opening a hot water outlet the boiler automatically responds to fire the boiler and supply the water-to-water heat exchanger with hot water via the three port valve.
You can set it back by switching OFF dip switch number 3. Remove the chamber cover by releasing all the screws should be two on each side.
Hot water will flow till the faucet is closed. This item is not curently in our warehouse. Primary pressure sensor- it is hydraulically operated sensor that checks and monitors water shortage and water general pressure in the main circuit.
The wall on which your appliance will be mounted should be able to support the weight of the boiler for an extensive period of time. Heatline Star 24 Boiler problem!!! Most plumbing and gas heating spares can be delivered next day before 12 to most of the UK. As you have already saved the maximum of 9 manuals to your online services account you need to delete one of these before you can save another one.
Permanent temperature difference between flow and return heating sensors.
Ideal Mini C28
As Kev says the diverter valve has failed. Discussion in ‘ Plumbing and Central Heating ‘ started by r1gaz10 Oct It wants to be fixed very soon or im afraid thats it as far as the landlord goes with regards to me paying anymore rent!! Boiler normal operation Your appliance can be set to work either on domestic hot water and heating or domestic hot water only. Verify the igniter unit connections.
Heat Line C28 Manuals
Collectively we have over years of experience in boiler spares identification and spares distribution. Verify that the appliance DSN code on the screen matches the product code of the manuao.
Locate the central heating sensor — it is on left side of the combustion chamber on the outlet of the primary heat exchanger as shown on the picture below 4. Ensure all joints are sound. Whilst every attempt is maanual to ensure the accuracy of information contained on this help centre, errors can occasionally occur.
Fit the manuak body in reverse order ensuring that the pump washers are sound and fitted correctly and the polarity of the electrical connections are correct.
Bars, Grates and Grills. Verify the boards reference. Fit the manifold with new burner injectors and tighten, ensuring that the injector size, marked on each injector is the same for the type of gas being used.
Verify the sensor F76 Thermal fuse fault Verify the fuses connections.