Wire the LCD RKP as shown in the wiring section of this manual. Replace the .. The Eurosec CP8 LCD has two log modes. These are: a). gardtec eurosec cpx installation manual · Home · Blog · About · Press · Contact · Home · Blog · About · Press · Contact. Powered by カスタマイズ可能なテンプレート . A range of alarm system user guides and manuals for owners and clients. Accenta 6 · Euro 46 User Manual · Euro Mini User Guide · Eurosec CP7/CP8 LED .

Author: Gronris Yozshulkree
Country: Belgium
Language: English (Spanish)
Genre: Health and Food
Published (Last): 27 April 2005
Pages: 296
PDF File Size: 4.44 Mb
ePub File Size: 10.87 Mb
ISBN: 950-1-73268-301-9
Downloads: 95039
Price: Free* [*Free Regsitration Required]
Uploader: JoJodal

Duress Codes may also be used on this system for activating Personal Alarms P. Posted 31 December – Under no circumstances should the actual user code be written down. At this ihstallation the system will revert to battery back-up The battery will only have a limited time that it can sustane the system for.

If the system is Unset when the Tamper occurs the alarm will be internal sounders only. Refer to the System Attributes section for what zones have been programmed as Part Set zones.

Normal To set the system with a normal keyswitch, insert the key and turn to the ON position then remove the key. The top line of the display will then be blanked off.

Setting or Unsetting the system using the code that is programmed as User 7 will activate a Duress signal. If you require a blank space press YES while the ‘-‘ is displayed 14 As you press YES for the ninth character or if you have jumped from step 9 the display will change to: Press 0 to escape.

Manusl remove is only effective for the one set. Press Yes Year is ok? I mean do some kind of connection or make any changes through the keypad? You currently have javascript disabled. Local legislation may prevent the use of Duress signals. If you let me know your order number we can send you an engineering manual for the panel. The Proximity Reader may be built in to the keypad or be an external reader that is mahual into a doorframe etc. Read Log 01 JAN I have linked the unused zone and it seems to be working fine.


Posted 05 January – The display will show: The display will clear once the power is restored. Follow the instructions for programming User Codes onto your system up to the point when you would enter the User Code. System Tampers The full security system is tampered, any attempt to remove covers from Keypads, Control Panel, Keypads, Bell Box es or detectors will cause a tamper alarm.


Because the G-Tag uses Manjal Technology there are no batteries to change in the unit, it is small enough to be carried on the users key ring and one Tag may be used on multiple security systems and some door entry systems. In this instance using will send a Duress code to your central station when you Set or Unset your system.

Several functions may not work. Before Vo-Comm can work several options will need to be programmed. If your system has remote communications fitted your installation company may have programmed the system so that you initialise the Access Remote call usually on lines with incoming calls barred. Please re-enable javascript to access full functionality. If the system was Unset only the internal sounders will operate. installatiln

About – gardtec eurosec cpx installation manual

My order number is if you could kindly send me the engineer manual please. At the end of the message eursec will hear a single tone, at this point press a key on your telephone keypad twice.

Community Forum Software by IP. A fault sounder will start, enter a valid User Code to stop the fault sounder. If this option has been invoked by your installation company the Set or Unset Status will only be displayed for ten seconds when the system is Set or Unset.

At this point present you Tag to the Proximity Reader and a code will be entered for you. Press No until the require level of code is shown Refer to page 3 for code level details. If your installation company has given you keyswitches for the operation of your system some user codes may have been reserved for use by these keyswitches. Page 7 Enter Zone No. The system may only be Reset when the Tamper has been cleared, otherwise another Tamper alarm will be generated.


Then choose Can or Cant Unset dependant on your requirements. I am using only 6 zone, should I leave the 2 zone as there are on the panel or do I need to do anything with them? I assume you have recieved it ok?

It should be noted that VoComm should not under any circumstances be used to ring the Emergency Services directly. Follow the normal instructions to the end for programming codes.

How do I change the master default code of ? OR Press No display will show: Keypad Tamper The keypad will monitor the number keys that are pressed without a valid User Code being entered. If the code already exists or is a duress of another code an error will be shown, choose another code and return to step 6 7 The display will show: Your installation company will have informed you as to the type of reset that your system is set for.

G-Tag Fob Legislation contained within DD does not allow for the transmission of confirmed alarm signals once the entry time has started if the user of the security system is using a manual code entered into the keypad. Press No until the setting you require is displayed Yes or No.

Please take time to familiarise yourself with the type of equipment fitted to your premises as it will prove invaluable whilst using this manual.