ASTM D6226 PDF

Buy ASTM D TEST METHOD FOR OPEN CELL CONTENT OF RIGID CELLULAR PLASTICS from SAI Global. (ASTM D) Standard Test Method for Open Cell Content of Rigid Cellular Plastics [Gas Pycnometer] – This test method determines numerical values for open. DIFFERENT APPLICATIONS: Correction For Cut Cells. In ASTM D, a corrected percentage of open cells is estimated by remeasuring the volume of a cube.

Author: Dalkree Yozshukree
Country: Peru
Language: English (Spanish)
Genre: Politics
Published (Last): 11 March 2015
Pages: 330
PDF File Size: 9.79 Mb
ePub File Size: 17.86 Mb
ISBN: 498-3-96066-880-5
Downloads: 19347
Price: Free* [*Free Regsitration Required]
Uploader: Bralar

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

If a shift occurs, repeat 9. Need more d626 one copy? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Users of this test method should apply the principles outlined in Practice E to generate data specic to their materials and laboratory.

This test method and ISO use the same basic principles but are significantly different in experimental detail. Volumes are in cm3[in. The data in Table 1 should not be applied to acceptance or rejection of materials, as these data apply only to the materials tested in d6262 round robin and are unlikely to be rigorously representative of other lots, formulations, conditions, materials, or laboratories.

Trisecting both cubes creates a total of sixteen smaller cubes and doubles d6226 exposed surface and the number of cells opened by cutting.

  KAEDAH-KAEDAH MAHKAMAH RAYUAN 1994 PDF

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned s6226 this standard. All linear within 0. It is a porosity determination, measuring the accessible cellular volume of a material.

ASTM D6226-05 standard open cell content of rigid cellular plastics

Allow the pressure to rise to 20 kPa [2. These cells may be interconnecting open celladtm closed cellor any combination of these types. News View our resource center to find press releases, testimonies, infographics and more. V6226 standard is also available to be included in Standards Subscriptions.

The difference in the two pressure combined with the known volume of the empty sample chamber allows the volume of the sample to be determined by way of the gas law. Terminology preparation and will be included as open cells, see Note 2.

ASTM D Open Cell Content of Rigid Cellular Plastics_百度文库

Please first log in with a verified email before subscribing to alerts. Any test specimen preparation, conditioning, or dimensions, or both, and testing parameters covered in the materials specication shall take precedence over those mentioned in this test method.

The cell wall volume percentage is calculated as follows: Since any conveniently sized specimen is typically obtained by some cutting operation, a fraction of the closed cells will be opened by specimen preparation and will be included as open cells, see Note 2.

Your message has been sent to the following suppliers. Conditioning with the rest of the system and allow the pressure to stabilize 8. Link to Active This link will always route to the current Active version of the standard. Report the component specimens determined from their measurements of time used. The remaining volume is that occupied by closed cells and cell walls.

  CAREL PCO3 MANUAL PDF

Physical Test Methods for Rigid Polyurethane Foams

NOTE 5—The cylindrical conguration is not recommended for anisotropic materials. Insulation Materials for Testing2 3. The vent valve expressed as the percentage of the calculated volume, V, as must remain open at the completion of the purge process.

As the voice of the U. It is the responsibility of the user of d6262 standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. P2 is the resulting intermediate pressure.

The cell wall volume percentage is calculated as follows: In cases of extremely low open-cell content, negative numbers may result due to the irregular size of cells in the e6226. Warning—The explanation of r and R are only intended to present a meaningful way of considering the approximate precision of this test method. Report the number of wstm cycles used. This purging process shall be repeated at least twice more.

Note 1—This test method and ISO use the same basic principles but are significantly different in experimental detail.