74LS688 DATASHEET PDF

Texas Instruments 74LS Logic Comparators are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments . December INTEGRATED CIRCUITS. 74HC/HCT 8-bit magnitude comparator. For a complete data sheet, please also download. Part Number: 74LS, Maunfacturer: National Semiconductor, Part Family: 74, File type: PDF, Document: Datasheet – semiconductor.

Author: Taunris Akinor
Country: Congo
Language: English (Spanish)
Genre: Finance
Published (Last): 16 July 2007
Pages: 360
PDF File Size: 20.89 Mb
ePub File Size: 5.10 Mb
ISBN: 169-3-84624-233-9
Downloads: 20428
Price: Free* [*Free Regsitration Required]
Uploader: Zologami

It is a glitchy signal. You could then use it as a clock. It might work, but I don’t like it much. You can’t use it while the inputs are changing.

There may be better ways to do this job so keep tinkering. Hi I doubt you’ll be able to run the output of the directly to a clock.

It’s comparing the high four address bits to a 4-position DIP switch. I’m currently designing the power-on-jump circuit for my processor board.

Comparator 74LS DIP20 | GM electronic COM

As the datxsheet lines transition and settle out, they might very well set up a glitch that agrees with the test condition, well before you intended. This sets the D-type flip flop, which switches off the NOP generator and turns on the bus tranceivers. It may even make it worse. It’s an 8-bit comparator, but it’s cheaper than the 74LS85 and has an enable input.

  LANDESBAUORDNUNG HESSEN PDF

74LS datasheet & applicatoin notes – Datasheet Archive

Here’s the pieces relevant to Power on Jump: This would also add about 62 nS to your latch clock which right now is only 3 gate delays long and would be difficult to see on an old low bandwidth scope.

I’m not that good with circuit design, but is it possible a monostable multivibrator one-shot would 744ls688 the job? Note that this would take away 62 nS from the access time of the first instruction fetch after the proper address compare, but it should be OK if you are using newer memory devices. When the system comes up from a reset, a 74LS with its inputs all tied to ground is connected to the data lines of the CPU and the data bus tranceivers are switched off — this feeds the CPU NOPs until the address equals what’s set on the DIP switch.

74LS688 Datasheet

I’ve never had to use one. Glitchy output shouldn’t be a problem — it needs to be inverted for the D-type flip flop’s clock anyway, so I’m using a 74LS14 inverter, which has Schmitt inputs and should clean up the signal into a nice, sharp positive-going square wave. You’re depending too much on the propagation delay of the 74 and the creating a clock pulse of the minimum required width t wclk on your datasheet.

  ARANYA COMMUNITY HOUSING PDF

In other words, what function does it serve?

I’m not talking about little tiny noise spikes. Just to scratch my own curious itch, what does the connect to? My calculations say yes, with lots of time to spare, but I’d like others’ opinions. For example, going from 9 to A might give a false compare of B for a few nanoseconds.

A way to avoid that would be to de-glitch the circuit by adding a synchronizing flip-flop running satasheet 16MHz just before the latching flip-flop.

Any decoder, like the will create big nasty full swing glitches that can only be removed with the proper dataheet gating or latching. This might cause a false trigger if your address trap was at B.

I don’t do well with word descriptions of circuits–can you draw a schematic? This is all fine. If you expect to use it, you need to turn the enable off during the time when the compare inputs are in transition.

I got lost reading that. Glitchy output shouldn’t be a problem — glitch, I see how you got your nickname. Hi No it won’t.